Certification Exam Prep Questions For Cisco Certified Network Professional


QuickStart is now offering assessment questions for Cisco Certified Network Professional. Whether you are deciding which exam to sign up for, or simply want to practice the materials necessary to complete certification for this course, we have provided a practice assessment to better aid in certification. 100% of the questions are real questions; from a recent version of the test you will take for Cisco Certified Network Professional


Arrow
 

1

What is a common design factor that you must consider when it comes to a hybrid VPN?

A. Packet encapsulation
Incorrect.
B. QoS
Incorrect.
C. Decrease MTU
Correct!
D. Increase MTU
Incorrect.
2

Which of the following is not a characteristic of multipoint GRE (mGRE)?

3

Which IP Security (IPsec) feature ensures packets being sent are not duplicate packets?

A. Integrity
Incorrect.
B. Confidentiality
Incorrect.
C. Authentication
Incorrect.
D. Antireplay
Correct!
4

Which of the following components are not components of a service provider’s Multiprotocol Label Switching (MPLS) cloud?

5

Which of the following are well-known advantages of IPv6 when compared to IPv4?(Select 3 answers)

6

This chapter discussed how may options for dynamic IPv6 global unicast address assignments?

A. Three
Correct!
B. Five
Incorrect.
C. Six
Incorrect.
D. None of these
Incorrect.
7

Which of the following does an IPv6 host use to learn the IP address of a default gateway on its subnet?

A. Stateful DHCP
Incorrect.
B. Stateless DHCP
Incorrect.
C. Neighbor Discovery Protocol
Correct!
D. Stateless Autoconfiguration
Incorrect.
8

Which of the following are the biggest drivers to move to IPv6 versus remaining on IPv4?(Select 2 answers)

9

Which of the following statements are true regarding the EIGRP neighbor command?(Select 2 answers)

10

Which of the following is intended to be a tiebreaker if two EIGRP paths have equal metrics?

A. Bandwidth
Incorrect.
B. Delay
Incorrect.
C. Maximum transmission unit (MTU)
Correct!
D. Reliability
Incorrect.
11

Which of the following commands displays all successor and feasible successor routes known to the router?

A. show ip protocols
Incorrect.
B. show ip route
Incorrect.
C. show ip eigrp neighbor
Incorrect.
D. show ip eigrp topology
Correct!
12

Which of the following multicast IP addresses is the designated EIGRP multicast address?

A. 224.0.0.5
Incorrect.
B. 224.0.0.6
Incorrect.
C. 224.0.0.9
Incorrect.
D. 224.0.0.10
Correct!
13

Refer to the figure. A network engineer is brought into a client network to configure the EIGRP stub feature on all appropriate devices. On which of the devices labeled in the figure should the engineer configure the EIGRP stub feature?

A. The Hub1 router
Incorrect.
B. The Branch1 router
Correct!
C. The Hub1 and Hub2 routers
Incorrect.
D. The Hub1 and Branch1 routers
Incorrect.
14

When a Cisco router sends EIGRP messages out an interface, what percent of the bandwidth is defined by default with the bandwidth command?

A. 75%
Incorrect.
B. 25%
Incorrect.
C. 100%
Incorrect.
D. 50%
Correct!
15

When configuring a Spoke router in an EIGRP network, what is the easiest way to limit the Hub routers from sending EIGRP queries to the Spoke device?

16

Refer to the figure. If the network administrator were trying to prevent the hub router from sending EIGRP query messages to the branches, according to Cisco best practices, which feature would best provide this behavior?

17

Which of the following settings are available under the address family configuration mode?

18

Which of the following are common features for EIGRP IPv6 and IPv4?(Select 2 answers)

19

You wish to configure your router to use EIGRP for IPv6 routing. Which of the following commands should be entered first?

20

Which of the following is the name of the OSPF packet that holds detailed topology information, specifically LSAs?

21

Which of the following statements accurately describe behavior when OSPF is enabled on a router?(Select 2 answers)

22

OSPF uses a router ID (RID). Which of the following is a step when determining the RID?

23

How many LSA (link-state advertisement) types are there in OSPF?

A. 11
Correct!
B. 7
Incorrect.
C. 8
Incorrect.
D. 9
Incorrect.
24

Which of the following LSA (link-state advertisement) types is created by ABRs to represent subnets listed in one area’s Type 1 and 2 LSAs when being advertised into another area?

A. Type 5
Incorrect.
B. Type 3
Correct!
C. Type 7
Incorrect.
D. Type 4
Incorrect.
25

Which of the following OSPF neighbor states is when a Hello has been received from the neighbor, it has the router’s RID, and all neighbor verification checks have passed?

A. ExStart
Incorrect.
B. Exchange
Incorrect.
C. Loading
Incorrect.
D. 2-Way
Correct!
26

The area range command in OSPF defines which of the following parameters?

27

What command would be used to filter OSPF LSA Type 3 traffic matching a prefix list named test-filter from entering into area 10?

28

R1(config)# ip prefix-list filter-area-51 seq 5 deny 192.168.1.0/24 R1(config)# What is the result of the following commands? ip prefix-list filter-area-51 seq 10 permit 0.0.0.0/0 le 32 R1(config)# router ospf 1 R1(config-router)# area 51 filter-list prefix filter-area-51 in?

29

Refer to the figure. What information can be learned about the route for the 60.60.60.0/24 network?

30

Refer to the exhibit. What is the result of the redistribute command with its reference to the route-map?Exhibit

PDP Url

Cisco Certified Network Professional


Beginner

Difficulty

Course Info

Download PDF

Certificate

See Sample

Buy Individually
Courses Offered In This Certification

Outline

Practice Certification Exam

More Information

More Information
Lab Access No
Difficulty Beginner
Language English

Reviews

Contact A Learning Consultant


click here