Which routing methodology is currently in use?
Which two statements about the connectivity are true? (choose two)
On which device does the fault condition exist?
To which technology is the fault condition related?
Which two commands issued on Corporate Router would resolve the fault condition that currently exists? (Choose two.)
You manage a network that uses a dedicated monitoring system. You examine the traffic and receive the output shown in the exhibit. Which network protocol has the highest amount of traffic?
Which interior routing protocol is considered a link state routing protocol?
You manage the network shown in the exhibit. Where should you apply an access list to block SSH traffic from Servers 1-3 to Server4?
What are the two main advantages of FlexStack-Plus over FlexStack? (Choose two.)
Which four optional statics are available when performing a path trace using APIC-EM? (choose 3)
You are in the process of configuring Internet connectivity for one of your branch offices over an ADSL connection. Your ISP will provide you with a dynamically assigned IP address for your external connection and you will configure Network Address Translation (NAT) on the router. To complete the external connection configuration, you will need to configure both the externally facing Ethernet interface and the Dialer interface. To properly configure the externally facing Ethernet interface, which two interface configuration mode commands should you apply? (Choose two.)
You are configuring the network with the topology shown in the exhibit. The relevant output from each switch is also shown in the exhibit. You discover that the switches do not create an etherchannel group. What should you do?
- A. From Switch2, run the port-channel load-balance src-mac command. From Switch1, run the channel-group 5 mode on command.
You manage the network shown in the exhibit. Which interface or interfaces should be designated as the monitored ports for a SPAN session?
Based on the information provided in the exhibit, which SNMP mode has been configured on the router?
Which three statements about routing protocol neighbor authentication on Cisco routers are correct? (Choose three.)
Based on the output in the show etherchannel port-channel command from Core_SwA shown in the exhibit. which method was used to create port-channel 1?
Spanning Tree Protocol (STP) uses the Bridge ID (BID) to dynamically elect a Root Bridge. The BID is composed of which two parts? (Choose two.)
Which two statements are true regarding the partial output of the show ip bgp summary command on R1 shown in the exhibit? (Choose two.)
You find the following line in the debugs of a ppp negotiation process between two routers: Phase is ESTABLISHING. Finish LCP What is the next message confirming the negotiation status?
What is the purpose of a controller as it relates to data center infrastructure management?
- A. The controller aggregates bandwidth from network devices that are not in use so that bandwidth can be used on demand or sold to trusted partners.
Which two statements accurately describe valid Link Aggregate Control Protocol trunking types? (Choose two.)
- A. Active: LACP packets are sent to peers and a channel will be formed if the peer is in an active or passive mode.
- B. Desirable: The link aggregation will only be formed if it receives a LACP packet. It will not send LACP packets.
- C. On: The link aggregation is created without negotiation. The switch automatically sends and accepts LACP packets.
You are the network administrator for your organization and you want to establish a Point-to-Point Protocol (PPP) WAN link using Cisco routers between the headquarters where you are located and a remote branch office. According to the security policy, Challenge-Handshake Authentication Protocol (CHAP) needs to be configured on the PPP link. You are analyzing the CHAP processing between the routers. Which three statements are true? (Choose three.)
What is the Extended System ID portion of a Spanning Tree Protocol (STP) Bridge ID (BID) used to identify?
What are the three possible ways to configure EtherChannel groups? (Choose three.)
Based on the information provided in the exhibit, what is the Spanning Tree port role for interface Gi0/1 on Sw_4, assuming that you are running the default Per-VLAN Spanning Tree Protocol Plus (PVST+)?
Router R1 has been configured using the following IP addresses: GO/1: 192.168.91.6/29 GO/2: 192.168.92.1/30 Default route: 192.168.92.21 using GO/1 You connect PC1 to GO/1 and assign PC1 the following IP addresses: IP address: 192.168.91.5/29 Default gateway: 192.168.91.6 PC1 fails to ping a network behind R1. What is causing the problem?
Which framework is commonly used for key distribution and authentication in wireless and wired networks?
Which administrative distance value is correct?
You enable EIGRP using the commands shown in the exhibit. You cannot see any EIGRP neighbors. What should you do to fix the problem?
Which Rapid Spanning Tree Protocol (RSTP) port role exists only when a switch has two or more trunk connections to a shared Local Area Network (LAN) segment?
About Individual Course:
|Learning Style||Self-Paced Learning|
|Course Duration||1 Hour|