Implementing Cisco IP Routing (CS-ROUTE)
|BUY INDIVIDUALLY||BUY AS SUBSCRIPTION|
When you subscribe, you get:
Master Plus subscription plan gives you access to this course PLUS:
About this Course:
Foremost, students need to get acquainted with the concept of IP Routing. It is a grand term used to define a set of protocols that figure out the path which data responds to and follows for transition across various networks from the source to its destination. The IP Routing protocols aid routers in setting up a forwarding table that corresponds the eventual destinations with next hop addresses.
The course, Implementing Cisco IP Routing v2.x (ROUTE), is an instructor-featured, 5-day advance level training targeting students to help them prepare for Cisco CCNP certification. The ROUTE course is a part of the CCNP Routing and Switching training material. The aim is to facilitate students in establishing their expertise from the knowledge gained from CCNA Routing and Switching and build their competencies for planning, executing, and monitoring a scalable routing network. The entire curriculum of this new ROUTE training mainly emphasizes on lab-based learning.
This course will also help you prepare for the Cisco 300-101 ROUTE: Implementing Cisco IP Routing exam.
A Cisco Certified Network Engineer is expected to earn an average of $77,484 per year.
After the course completion, students should be able to:
Understand and explain routing protocols and various remote connectivity choices along with their significance and influence on routing and executing RIPng
Configure EIGRP in IPv4 and IPv6 environments
Configure OSPF in IPv4 and IPv6 environments
Execute route redistribution by employing filtering mechanisms
Incorporate path control through policy-based routing and IP SLA
Facilitate enterprise internet connectivity
Safeguard Cisco routers as per the officially declared best practices and configure authentication for routing protocols
This course is intended for students who plan to become network professionals and for who those who have gained ample knowledge from Cisco CCNA courses. Some standard job titles you may be entitled to include network engineers, support engineers, network technicians or system engineers.
Here are some of the prerequisite information points that students are expected to possess and display before pursuing this course:
Explain the fundamentals of networking
Enable Internet and WAN connectivity (IPv4 and IPv6)
Perform network device security management
Run a mediocre-sized LAN with many switches, backing VLANs, trunking and spanning tree
Troubleshoot IP connectivity (IPv4 and IPv6)
Configure and troubleshoot EIGRP and OSPF (IPv4 and IPv6)
Configure devices for accessing SNMP, syslog and NetFlow
Handle the Cisco device configurations, Cisco IOS images, and licenses
Recommended Prerequisite Courses:
Virtual Instructed-Led Outline
Module 1: Basic Network and Routing Concepts
- Lesson 1: Differentiating Routing Protocols
- Lesson 2: Understanding Network Technologies
- Lesson 3: Connecting Remote Locations with the Headquarters
- Lesson 4: Implementing RIPng
Module 2: EIGRP Implementation
- Lesson 1: Establishing EIGRP Neighbor Relationships
- Lesson 2: Building the EIGRP Topology Table
- Lesson 3: Optimizing EIGRP Behavior
- Lesson 4: Configuring EIGRP for IPv6
- Lesson 5: Discovering Named EIGRP Configuration
Module 3: OSPF Implementation
- Lesson 1: Establishing OSPF Neighbor Relationships
- Lesson 2: Building the Link-State Database
- Lesson 3: Optimizing OSPF Behavior
- Lesson 4: Configuring OSPFv3
Module 4: Configuration of Redistribution
- Lesson 1: Implementing Basic Routing Protocol Redistribution
- Lesson 2: Manipulating Redistribution Using Route Filtering
Module 5: Path Control Implementation
- Lesson 1: Using Cisco Express Forwarding Switching
- Lesson 2: Implementing Path Control
Module 6: Enterprise Internet Connectivity
- Lesson 1: Planning Enterprise Internet Connectivity
- Lesson 2: Establishing Single-Homed IPv4 Internet Connectivity
- Lesson 3: Establishing Single-Homed IPv6 Internet Connectivity
- Lesson 4: Improving Resilience of Internet Connectivity
- Lesson 5: Considering Advantages of Using BGP
- Lesson 6: Implementing Basic BGP Operations
- Lesson 7: Using BGP Attributes and the Path Selection Process
- Lesson 8: Controlling BGP Routing Updates
- Lesson 9: Implementing BGP for IPv6 Internet Connectivity
Module 7: Routers and Routing Protocol Hardening
- Lesson 1: Securing Cisco Routers
- Lesson 2: Describing Routing Protocol Authentication Options
- Lesson 3: Configuring EIGRP Authentication
- Lesson 4: Configuring OSPF Authentication
- Lesson 5: Configuring BGP Authentication
The following discovery labs are included in this course:
- Discovery 1: Configuring RIPng
- Discovery 2: Configuring and Investigating Basic EIGRP
- Discovery 3: Building The EIGRP Topology Table
- Discovery 4: EIGRP Stub Routing
- Discovery 5: EIGRP Summarization
- Discovery 6: EIGRP Load Balancing
- Discovery 7: EIGRP for IPv6 Configuration
- Discovery 8: Discovering Named EIGRP Configuration
- Discovery 9: Basic OSPF Configuration Introduction
- Discovery 10: Building the Link-State Database
- Discovery 11: OSPF Path Selection
- Discovery 12: OSPF Route Summarization
- Discovery 13: OSPF Stub Areas
- Discovery 14: Implementing OSPFv3
- Discovery 15: Basic Redistribution
- Discovery 16: Manipulate Redistribution
- Discovery 17: Manipulate Redistribution Using Route Maps
- Discovery 18: Analyzing CEF
- Discovery 19: Implementing PBR
- Discovery 20: NAT Virtual Interface
- Discovery 21: Basic IPv6 Internet Connectivity
- Discovery 22: Basic BGP Configuration
- Discovery 23: Influencing BGP Path Selection
- Discovery 24: BGP for IPv6
- Discovery 25: Configuring EIGRP Authentication
- Discovery 26: OSPF Authentication Configuration
The following challenge labs are included in this course:
- Challenge 1: Configure RIPng
- Challenge 2: Configure EIGRP
- Challenge 3: Configure and Optimize EIGRP for IPv6
- Challenge 4: Implement EIGRP for IPv4 and IPv6 Through Named Configuration
- Challenge 5: Configure OSPF
- Challenge 6: Optimize OSPF
- Challenge 7: Configure OSPFv3
- Challenge 8: Implement Redistribution Using Route Filtering
- Challenge 9: Implement Path Control
- Challenge 10: Configuring BGP
- Challenge 11: Configure Authentication for EIGRP Routes
- Challenge 12: Configure BGP Authentication
|Learning Style||Virtual Classroom|
|Course Duration||5 Days|
Frequently Asked Questions About Virtual Instructor-Led Courses
I can't connect to my class, what are my options?
The link to the class is available upon logging in to your dashboard. If you are unable to see it, please contact our support team at 1-855-800-8240 and they will be happy to provide you the direct link via email or the dial in number.
I can't make it to attend to class. Can I reschedule?
Yes, you can reschedule your class. Please contact your Sales representative and they will arrange this for you. If you forgot his/her name, feel free to contact our support team at firstname.lastname@example.org or 1-855-800-8240.
Will I get my certificate upon completion?
Yes. Upon completion of the course, it will be available on your course as a Trophy Icon for you to download. If you do not see this, you will need to contact email@example.com with the following details so they can email you the certificate: Class Name, Class Date, Account Rep, and Your Email.
I cannot connect to my lab. Help!
Your Lab is accessible on the bottom part of your course. You will see a button that says "LAB". Just click it to launch the lab. Please note that some classes don’t need/require a LAB. You can verify with our support team by calling them at 1-855-800-8240 or by email at firstname.lastname@example.org. You can also check with your Instructor or the Associate Instructor if your class includes one.
What is my access code for Skillpipe?
A. Not all of the classes have or require Skillpipe. If your class includes one, please check your email as you should have received one from email@example.com. In case you do not find it in your inbox, please check the Spam / Junk folder. For any further assistance, you can call the support at 1-855-800-8240 or contact them via email at firstname.lastname@example.org.
I don't have audio. I can't hear the instructor.
Make sure you are using a compatible headset for your laptop or computer. If you don’t have a headset, you can use the built-in speaker of your laptop. Otherwise, you can use the dial in option by calling the dial in number provided in the class joining email. You may also contact support team for the dial in numbers associated for your training at 1-855-800-8240 or contact them via email at email@example.com.
How can I reach student support?
Support can be reach via phone at 1855-800-8240; via email at firstname.lastname@example.org or via chat support through the chat button on our website. Please note that support office hours will be from 8am-5pm CST Monday to Friday. Any concerns after office hours will be attended the following business day.
Get A Team Quote or Got Questions?
- Personalize learning based on competencies, goals & tools
- Expert Mentoring
- Hands on Labs & Assignments
- AI Curated Digital Book Content
- Adaptive Learning Paths
- Analytics & Benchmarking
- High certification Pass Rates – Over 200,000 people certified and more than 95% of our learners pass their certification on the first attempt